USE: 20% solution in water

APPLICATION: Blackfast 183 will darken bright brass surfaces to a dark brown. The bath should be maintained at a temperature range 35-40 C for the best results. At lower temperatures, the process is slower and the recommended immersion time of 5 minutes is exceeded. At temperatures higher than 40 C, some ingredients in the solution begin to dissociate rendering the process inoperative. On removal from the solution, the brass is allowed to dry then lightly abraded to remove some of the coating on proud surfaces. What remains will be within the crevices and surface of the brass revealing an antiqued surface.

TANK CONTROL:

Tanks should be of plastic, rubber lined steel or stainless steel. When in regular use the performance of Blackfast 183 can be monitored readily by the practical results. In addition, a simple test can be undertaken to check the strength of the tank solution. From a 20% solution of Blackfast 183 in water, take 10 ml of the tank solution and place in a transparent conical flask. Add a few drops of bromocresol green indicator solution.

The contents of the flask are titated with a test solution until the original yellow colour has changed to blue. Consumption of 20 ml of the test solution indicate a tank of the correct strength. For each 1 ml shortfall from a reading of 20 ml, it is necessary to add 0.75 % Blackfast 183 concentrate (i.e. for a 100 litre bath, add 0.75 litres 183).

Blackfast 183 antiquing black is part of the Blackfast range of products for the chemical blacking of iron and steel at room temperature

Blackfast Chemicals continues to improve the quality and performance of its range of products and reserves the right to modify product formulations without prior notice.

SAFETY DATA :

1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND OF THE COMPANY

PRODUCT NAME: BLACKFAST 183 ANTIQUING SOLUTION
APPLICATION: Antiquing of brass at room temperature
COMPANY: Blackfast Chemicals
ADDRESS: 78 Coombe Road, New Malden, Surrey KT3 4QS, England
TEI/FAX NO’S: Tel: 0181-336 2900 Fax: 0181-336 0909

2. COMPOSITION/INFORMATION ON INGREDIENTS

COMPOSITION: Aqueous solution of inorganic/organic salts.
HAZARDOUS INGREDIENTS: Selenium Compound <1% as Se.
SYMBOL: Xn
RISK PHRASES: R 20/22, R 33
EEC NO: 231 - 957- 4

3. HAZARDS IDENTIFICATION

Harmful

4. FIRST AID MEASURES

INHALATION: Remove to fresh air. Seek medical aid.
INGESTION: .Gargle, rinse mouth and drink plenty of water. Do not induce vomiting. Seek medical aid.
SKIN: Remove contaminated clothing and wash skin with plenty of water. Seek medical aid.
EYES: Flush with clean water immediately for 10 minutes. Seek medical aid.

5. FIRE FIGHTING MEASURES

Non flammable. Will not support combustion.
Decomposition products: Oxides of Carbon, Phosphorus, Selenium, Chlorine and Chlorine Oxides.

6. ACCIDENTAL RELEASE MEASURES

PERSONAL PRECAUTIONS: When dealing with a spill note the recommendations in Section 7
ENVIRONMENTAL: Prevent entry into drains, sewers and water courses.
SPILLAGE: Absorb liquid in absorbent clay granules.

7. HANDLING AND STORAGE

Avoid inhaling the vapour. Avoid contact with skin and eyes. Store in clean, dry conditions. Keep container closed and ensure label is intact and legible. Prevent from freezing.

8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Occupational Exposure Limits: Selenium Compound (as Se) 8 hr TWA 0.1 mgm-3 (EH 40/94). Cover when not in use. Local exhaust ventilation is recommended when in continuous use. Personal protection: Wear impervious (PVC) gloves, eye protection and plastic apron. Remove contaminated clothing immediately.

9. PHYSICAL AND CHEMICAL PROPERTIES

APPEARANCE:Blue liquid
SPECIFIC GRAVITY: 1.22 @ 200C
SOLUBILITY/MISCIBILITY IN WATER: Complete
FLASH POINT: N/A
DEGRADATION:Can occur above 500C
pH: 1.25

10. STABILITY AND REACTIVITY

Solution is stable under normal conditions. Avoid temperatures above 400C and below 50C. Irritant gases may be released above 500C. Avoid sources of ignition.

11. TOXICOLOGI CAL INFORMATION

The following toxicological information is based on the toxicity of the products principal hazardous component - Selenium Compound. Local contact may cause irritation of the skin and mucous membranes. Inhalation may cause coughing. Ingestion may cause vomiting and diarrhoea.

12. ECOLOGICAL INFORMATION

Not assessed.

13. DISPOSAL INFORMATION

Disposal must be in accordance with local and national legislation. Dispose through an authorised waste contractor to a licensed site.

14. TRANSPORT INFORMATION

No special precautions are necessary.

15. REGULATORY INFORMATION

HAZARDOUS INGREDIENTS: Selenium Compound
SYMBOL: Xn
RISK PHRASES: Harmful by inhalation and if swallowed. Danger of cumulative effects.
SAFETY PHRASES: When using, do not eat, drink or smoke. After contact with skin, wash immediately with plenty of water. In case of contact with eyes, wash immediately with plenty of water. In case of accident or if you feel unwell, seek medical advice (show the label where possible).
STATUTORY INSTRUMENTS: Health and Safety at Work Act 1974. Chemicals (Hazard Information and Packaging) Regs 1993 (Si 1746). Control of Substances Hazardous to Health Regs 1988 (Si 1657). Environmental Protection Act 1990.
CODES OF PRACTICE: Classification and labelling substances dangerous for supply (COP 22). Waste management: The duty of care.
GUIDANCE NOTES: Occupational exposure limits (EH 40). Classification, Packaging and Labelling of Dangerous Substances Regs. 1984 HS(R)22.

16. OTHER INFORMATION

Read the Application Data Sheet before using this or any Blackfast product. The product is intended for the stated use only. Do not use the product for any other application without obtaining advice from us beforehand.
If this product is for resale, ensure that the purchaser receives a copy of this information.
If this product is for end use, ensure that your employees and others who may be affected are aware of the contents of this sheet.